Draft Angle for Injection Molding: Design Guide and Best Practices

When we talk about the best practices for plastic injection molding parts, there are some that are unavoidable. Topping that list is usually the injection molding draft angle. Every injection molding design is aimed towards manufacturability. Therefore, you must consider every step of the process.

Although your parts may form correctly in the mold, problems may come up during the ejection process. This may give rise to unwanted defects in the molded parts. A draft angle will help avoid many of these unwanted issues. In this article, we will discuss the benefits of injection angles and a design guide for easy injection of your parts.

While we’ll cover more about the benefits later, let’s briefly describe a draft angle.

What is a Draft Angle?

A draft angle refers to that slant applied to the sides of most features of injection molded parts. Positioning of the injection angles is such that they run towards the direction of the mold’s pull and parting line. They help to release the molded parts from the mold easily.

99% of your injection molding design will require draft angle injection molding for a successfully made part. The angle tapers on the molded part’s surfaces. Therefore, the part can easily slide across the mold’s cavities and cores as you’re demolding.

Benefits of a Draft Angle

Many times, draft angles may create a conflict of interest. Molders like and recommend draft angles. However, mold-makers find it daunting to machine the angles on all cavity and core surfaces. Some also believe that draft angles may complicate the part designing.

However, it is crucial to note that draft angles offer an extensive range of benefits. They are vital to ensure that molded parts meet the required quality standard. Without a draft, you increase the chances of having injection molding issues. This may unnecessarily increase the cost of production and lead time.

Problems often arise from friction and vacuums when there is no draft designed into the part. These can damage your part. In extreme cases, the mold is also affected. Plastics shrink before cooling. Therefore, some portions of your part will likely pull away from the mold. Other portions will grip the core.

A draft angle allows you to use a simple push on the ejector pins to pop your part out of the mold. This way, you will prevent the part’s surfaces from being dragged along the mold when ejected. Friction between your part’s surface and the mold’s surface can cause scratches and affect your part’s appearance.

Furthermore, injection angles prevent the formation of vacuums during ejection. The absence of the draft may cause ejection pins to push on the component until stressing of the vacuum occurs. This may lead to the bending, breaking, or warping of the part when it is being ejected.

Adding draft angles to your design will help you avoid these problems. Therefore, you can improve the cosmetic finishes of your part and reduce the cost of production. A draft angle also helps you prevent elaborate and expensive ejection setups.

To sum up, adding injection angles to your design:

• Ensures smooth, uniform, unscratched finishes when required
• Reduces the possibilities of damage to parts due to friction during ejection
• Ensures the uniformity and integrity of other surface textures and finishes
• Reduces wear and tear on the molded part
• Reduces the chances of damaging the mold
• Minimizes warping to your geometry
• Reduces overall cooling time by eliminating or reducing the need for elaborate ejection setups
• Offer both direct and indirect reduction to overall production cost

Draft Angle Design Guide and Best Practices

First, you must note that there is no single adequate draft angle for all molded parts. Every individual part has its unique draft requirements. Larger parts may require more drafts than smaller ones. Also, thin-walled parts molded at high pressures may require more draft than those molded at lower pressures.

With that in mind, here are some general guides and best practices for draft design:

1. Most Parts Require a Draft Angle of 1½ to 2 Degrees

This is a rule of thumb that applies to molded parts with depths of up to 2 inches. With this size, a draft of about 1½ degrees is enough for easy release of parts from the mold. This helps to prevent damages to the parts when the thermoplastic material shrinks.

2. Draft Angle Should Average Additional Degree for Every Inch of Depth

This practice works best for larger or deeper parts. These kinds of parts require more drafts to account for the added surface area. The additional injection angles also account for the friction that occurs during mold release.

3. Draft Angle Should Be Present Towards the “Top” of the Mold

This means that the draft should follow the mold’s direction moving up or away as the separation occurs. Suppose you’re familiar with hollow boxes with drafted walls. In that case, you’ll notice that the open top is slightly wider than the bottom. This is a result of a correctly applied draft.

4. Textured Parts Would Usually Require More Draft

Some parts may have intricate textures designed on their surfaces. Others may have recessed or raised surfaces.

For such components, the draft angle should be added to the optimal 1½ to 2 degrees. The addition should be done at a rate of another 1½ degrees per 0.001’’ (thousandth-inch) of surface depth.

5. Every Component of a Piece Should Have Draft Angles

Materials with complex geometries or parts with tension-easing features should have draft angles. These features include gussets, louvers, ribs, and others. They are all crucial components of a good design. Consequently, any are of these features in contact with the mold should incorporate injection angles.

6. Incorporating Draft Angle Two Sides of a Part Offers Even More Benefits

Some materials (such as a solid cylindrical part) often have their parting line in the middle. In this case, both ends of the part should have draft angles. This is because two mold release actions are involved in this kind of operation.

7. Vertical Surfaces Should Have — At The Barest Minimum — Half a Degree of Draft

This guideline is important when the design requires a uniform angle from the bottom to the top of the vertical surface. Half a degree of draft offers an effective compromise for designs that require straight walls. It also helps the part to meet the injection molding requirements.

8. It is Always Advisable to Have a Draft Angle

It is important to reiterate this fact since many designers tend to resist incorporating a draft. Regardless of how small, engineers must always advocate for some degree of draft. A draft design is always best since it is unlikely for you to find a design case requiring a zero-degree angle. Remember the saying, “any draft is better than no draft.”

Read full article at https://www.rapiddirect.com/blog/injection-molding-draft-angle/